599 GTO and 360 Challenge Stradale Cuff

$ 145.00 
Please refer to size chart before ordering.

This variant is currently sold out

Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff

Affordable extravagance! This slender cuff is made from metal sourced from two different Ferraris -- a white 599 GTO in a pearl white, and from a 360 Challenge Stradale in rosso corsa. We cut, sanded, and polished the white 'base' cuff and after shaping, we added a section of the red metal. The 360 Challenge Stradale piece tapers from narrow to wide, culminating in a slanted angle towards the end. This entire piece is slightly offset so that part of the metal extends over the edge of the white cuff underneath. 

Taking car metal and turning it into beautiful jewelry is no easy task. Our artists spend a lot of time ensuring that each CRASH item meets our high standards for quality and design.  

We engrave the name of the car it came from inside the cuff. All CRASH jewelry is one-of-a-kind and handmade in our studio based in a body shop in Los Angeles. Your order will arrive in custom CRASH packaging with a Registration card. 3/4" wide

Please go here to figure out which size you should order.

Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff
Cuffs - Italian Red And White Cuff

How do I know what size Cuff to order?

Use a soft tape measure and wrap it tightly around your wrist above the bone. Note the measurement in inches and subtract 1/2" for the opening gap. For example, if your wrist measures 7" in circumference then you would order a 6.5". Please refer to our size chart and use our drop-down menu to select size.
If this is a gift please send us an email and we'll help you figure it out. 

For an instructional video on how to measure for a cuff go here.

 

It's a gift. I don't know their size.

If you are ordering a cuff as a gift and do not know the recipient's wrist size, we suggest that you stealthily locate their watch (assuming they wear a watch.)
Example:  We measured by pressing the entire watch down so it was flat. Then we marked where they fastened their watch (3rd hole from the end). Finally, we measured from just above the buckle to the 3rd hole which is approximately 7".

How do I put on a Cuff?

1. Turn your arm up and find a soft point on your inner forearm right above your wrist. (This is also referred to as the flat part of your upper wrist.)
2. Position the cuff in a 'C' shape and press into the soft spot on your forearm.
3. Press gently into the soft spot and roll your arm right into the opening of the cuff.
4. Slide the cuff down to the bottom of the wrist.
You can adjust the tightness of the cuff by gently squeezing it snug.
Most importantly: Do not force the cuff open as rivets may 'pop'.
5. To remove: slide cuff up to the flat part (soft spot) of your inner forearm and reverse the process.
Here is a video (not mine) that does a great job of explaining the technique.